Showing results: 1426 - 1440 of 1455 items found.
-
NLINE-U1553 -
Alta Data Technologies LLC
The NLINE-U1553 implements the latest USB 3 SuperSpeed technology for 1-2 dual redundant, independent 1553 channels. Full function capability for Bus Controller (BC), multi-RT (mRT), and Bus Monitor (BM). Also, o-scope signal capture on the first channel to troubleshoot bus signals. All built-in a small, rugged cable assembly that allows the customer to easily connect with standard 1553 jack connectors, or make their own custom cable with a Lemo break-away standard. USB 2 backward compatible (but not recommended – USB 3 offers superior throughput performance).
-
Bias-T PLUS -
Array Solutions
The Array Solutions Bias-T PLUS is a 1.8-148 MHz stand alone weatherproof unit that permits the application of DC control signals of up to 400ma on your coax cable. By inserting the control voltage on the coax cable feed-line, you eliminate the requirement for external DC wires for powering remote devices.The Bias-T PLUS weatherproof assembly means that it can be placed indoors or outdoors for maximum flexibility. Typically, one Bias-T PLUS will be placed indoors for inserting DC on your coax feed-line, and one Bias-T PLUS will be placed at the remote device where the DC voltage is extracted.
-
Praxsym
Low Noise Pre-Amplifier and companion external low noise amplifier (LNA) are used to amplify low level microwave signals. The Pre-Amplifier contains an AC/DC power supply, internal low noise amplifier, and a bias tee to source a DC bias voltage on the RF input connector.To overcome cable loss between the test antenna and the Pre-Amplifier assembly, a remote low noise amplifier (LNA) is mounted directly onto the 10 GHz antenna. A bias tee inside the Pre-Amplifier chassis powers the remote LNA through the coax cable interconnecting the pre-amplifier and the 10 GHz test antenna.
-
CKT1175-50 -
CK Technologies, Inc.
The CKT1175-50 is a high-voltage wiring analysis system that features a switching matrix that can be distributed around the workshop or in and around the assembly to be tested. This system is expandable in 100 or 150 test point increments to 96,000 test points, and is available with a variety of adapter cable interface connectors, with the standard being the CKT MAC interface system
-
510151108 -
Virginia Panel Corporation
QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. Allowing flexible configuration options with standard commercial connectors, QuadraPaddle modules are designed to fit any VPC pin and socket-based Mass InterConnect system. Available in 192 and 480 contact positions, QuadraPaddle modules accept standard .100” (2.54mm) pitch headers, breadboards, and connectors for direct PCB, ribbon cable, and other connections as well as discrete wiring.
-
510150131 -
Virginia Panel Corporation
QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. Allowing flexible configuration options with standard commercial connectors, QuadraPaddle modules are designed to fit any VPC pin and socket-based mass interconnect system. Available in 192 and 480 contact positions, QuadraPaddle modules accept standard .100” (2.54mm) pitch headers, breadboards, and connectors for direct PCB, ribbon cable, and other connections as well as discrete wiring.
-
510150135 -
Virginia Panel Corporation
QuadraPaddle modules are molded on .1” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. Allowing flexible configuration options with standard commercial connectors, QuadraPaddle modules are designed to fit any VPC pin and socket-based mass interconnect system. Available in 192 and 480 contact positions, QuadraPaddle modules accept standard .1” (2.54mm) pitch headers, breadboards, and connectors for direct PCB, ribbon cable, and other connections as well as discrete wiring.
-
510151127 -
Virginia Panel Corporation
QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. Allowing flexible configuration options with standard commercial connectors, QuadraPaddle modules are designed to fit any VPC pin and socket-based Mass InterConnect system. Available in 192 and 480 contact positions, QuadraPaddle modules accept standard .100” (2.54mm) pitch headers, breadboards, and connectors for direct PCB, ribbon cable, and other connections as well as discrete wiring.
-
Model 4861B OEM -
ICS Electronics
* 114578-24 board has 4 isolated analog outputs, 4 isolated analog inputs, 4 isolated drivers and 8 digital inputs* GPIB interface header includes GPIB address switch input signals.* Serial interface header includes RS-232 and RS-485 signals. Use the 114597 Serial Cable Kit to connect the serial signals to your rear panel* Use with any ICS GPIB Connector/Address Switch Assembly.* Runs on 12 Vdc regulated power.
-
JT 2147 QuadPOD -
JTAG Technologies Inc.
The JT 2147 QuadPOD high speed device programmer and flash programmer comprises JT 2148 transceiver and four independent, programmable JT 2149 TAP PODs and provides signal conditioning for the DataBlaster series of boundary-scan controllers. Used for gang, parallel, fast testing / Programming of devices.TAP pods can be housed integrally within the transceiver or they can be detached and reconnected via the (optional) one meter extension cable. The JT 2148 transceiver is available in standard (/10) or industrial (/13) variants. The /13 variant includes a SCSI cable splitter to allow system integrators to use flat ribbon cables into the transceiver itself which often simplifies fixture building.A fixture-embedded variant of the JT 2147 is available as part reference JT 2147/FXT. This unit integrates the function of the transceiver and four pod onto a single assembly. This variant can also support 64 DIOS channels and SCIL functions (see more images below for a picture of the JT 2147/FXT).
-
Teledyne Defense Electronics Storm Microwave
Storm Products has been producing high performance semi-rigid interconnects for over 20 years for a variety of markets, including: defense, telecom, wireless and test & measurement. Experienced in:- Cable sizes from 0.034" to 0.500"- Solid PTFE dielectric and high performance tape wrapped products- Wide variety of standard connector styles: MCX, SMA, SMB, SMC, TNC, N, 7/16, SC, and HN- Years of experience on blindmate connector styles: OSP GPO, GPPO, and GMSSpecialized experience in:- Applications where phase stability is critical- low intermod interconnects- High power designsManufacturing equipment:- Automated bending equipment and optical comparators - Programmable thermal chambers for pre-conditioning formed cables- Specialized assembly and soldering equipment for high volume applications- Automated network analyzers through 50GhzDue to the custom nature of formed semi-rigid cable assemblies, additional information is required before providing a quotation for your requirement.
-
Model 4804B -
ICS Electronics
* Provides RS-232C single-ended and RS-422/RS-485 differential serial signals. * Functions as a GPIB-to-Serial Interface (G-Mode) or as a Serial-to-GPIB Controller for a single device (S-Mode).* Over 600 Kbytes/second GPIB data transfer rate.* Transparent data transfer.* GPIB Address can be set by SCPI commands, by an external rocker switch or by a serial command.* On board voltage regulator for operation from 5 to 15 Vdc power.* Dual GPIB headers support GPIB connections with a GPIB Connector/Address Switch Assembly or with a GPIB Flat Ribbon Cable.
-
Model 4816 -
ICS Electronics
* Provides GPIB-to-serial and RS-232-to-RS-485 conversion path for serial devices with RS-485 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message.* On board voltage regulator for operation from 5 to 15 Vdc power.* Dual GPIB headers support GPIB connections with a GPIB Connector/Address Switch Assembly or with a GPIB Flat Ribbon Cable.
-
M.2-DIO-24A -
Acces I/O Products, Inc.
The M.2-DIO-24A is an M.2 card, and optional cable assembly (D-Sub 37-pin Male connector) designed to be easily panel-mounted in any application environment. It uses the high speed PCI Express bus to transfer digital data to and from the card. The digital I/O is compatible with 8255 PPI chips making it easy to program. This also allows for simple and trouble-free migration from other ACCES PCI and PCI Express digital I/O cards, but also provides for advanced features enabled by the onboard FPGA logic.
-
CR -
Cirris Systems Corporation
As a wire harness tester, a cable tester, a continuity tester, a component tester, and a guided harness-assembly aid, the Easy-wire CR tester is versatile. The easy-wire CR features Windows based software that allows you to create custom graphics of your connectors and light LEDs to guide the harness assembly process. Test Points: 256-32,000, Test Current: 6.5 mA max